Fiberglass fabric is woven glass fiber cloth sold in rolls, and its value comes from a short list of properties. It resists heat, corrosion and wear, it stays light for its strength, it can be cut, sewn and bonded, and it wets out quickly with polyester, vinyl ester and epoxy resin. Those properties explain where it is used, from boats and surfboards to electronic boards and pipe insulation jackets. This guide covers the properties of fiberglass fabric first. It then classifies the fabric by glass type, weave, weight, construction and coating, and covers applications and industry uses. Finally it turns them into a buying sequence: which numbers to confirm in writing, and where the supplier data still leaves gaps.
What Fiberglass Fabric Is And How It Is Made

Fiberglass cloth is made by melting ball glass, drawing it into filaments, twisting yarn, warping, sizing and weaving, then removing the size in a desizing step before inspection, packing and loading. ZS Fiberglass runs the drawing, twisting and weaving in house, which matters to a buyer because one plant controls both the yarn and the cloth, so a roll can be traced back to its yarn. Woven fiberglass in this form is a fabric of warp and weft yarns, supplied as a continuous fiberglass fabric roll of 110 to 130 yards on a cardboard core or tube. Samples are sent folded, so judge roll handling from the specification and not from a folded sample.
Properties Of Fiberglass Fabric That Affect Buying Decisions

Glass fiber fabric combines stable chemistry, wear resistance and low weight. This section is the single reference for performance parameters. The sections after it use these figures rather than repeating them.
- Heat resistance: every figure carries its time at temperature, and higher SiO₂ content gives higher temperature capability.
- Regular cloth (styles 3732, 3733 and 7628) is rated 550°C for half an hour and 770°C instantaneous.
- Medium silica cloth (over 70% SiO₂) is rated 800°C for 20 minutes and 1000°C instantaneous.
- High silica cloth (over 96% SiO₂) is rated 1200°C for 20 minutes and 1700°C instantaneous.
- The data sheet for 3732 gives a service temperature range of -120 to 550°C. The two regular-cloth statements use different time bases, so ask whether 550°C is a continuous service rating or a half-hour exposure before specifying a heat resistant fabric.
- Corrosion, rot and wear: the chemistry is stable, and the cloth resists rot and mildew and stands up to wear.
- Processing: it can be cut, sewn and bonded, and lightweight cloth wets out quickly.
- Resin compatibility: every style works with polyester, vinyl ester and epoxy resin, as long as the resin ratio is controlled before application.
Types Of Fiberglass Fabric By Classification Dimension

Fiberglass fabric is classified along five separate dimensions. Each answers a different question, so a single fabric is described by one choice from each (for example, E-glass, satin, 10 oz, biaxial, uncoated).
- Glass type: what chemistry and electrical behavior the fiber has (A, C, E, S).
- Weave pattern: how the cloth drapes and carries load (plain, twill, satin).
- Fabric weight: how thick and stiff each layer is (4 oz, 6 oz, 10 oz classes).
- Construction: in which directions the fibers are laid (woven, multiaxial, biaxial, unidirectional, triaxial).
- Coating: what extra surface function is needed (silicone, aluminized, PU, PVC, acrylic).
By Glass Type
The glass type sets the chemistry and electrical behavior.
| Glass Type | Alkali Oxide Content | Characteristics | Suited To |
| A | 15% or more | Made from broken or bottle glass and no longer used | Should not appear in a specification |
| C | 11.9 to 16.4% | Stable chemistry and good strength, but the high alkali content rules it out for electrical insulation | Chemical-resistant uses that are not electrical |
| E | Below 0.8% | Chemical stability, electrical insulation and strength are all very good | General composite and electronic use |
| S | Not classed by alkali | Rated about 35% higher in strength and 10 to 20% higher in modulus than E-glass, and rated to 800°C, but less flexible. The test basis for these figures is not published, so request it | Local high-strength areas only |
By Weave Pattern
- Plain weave: even, smooth and soft, with lower tensile strength and wear resistance. Suited to large smooth parts.
- Twill weave: good strength and durability. Suited to parts such as luggage racks and ship shells.
- Satin weave: rated the strongest of the three, and conforms best to curved surfaces. Suited to curved parts.
Treat “strongest” as a tendency, because published testing shows the answer depends on what is measured. In a 2023 study of woven glass fabric and epoxy laminates made by vacuum molding, satin gave the best flexural modulus, then plain, then twill, while twill had the better storage modulus near the glass transition temperature. A separate study of vacuum-infused laminates found that weave changed the fiber and void volume fractions, and that at similar fiber volumes the weave itself had little effect. Choose weave first for drape and shape, then confirm strength on a test panel in your own resin and process.
By Fabric Weight
Weight in g/m² affects density and thickness. Lightweight cloth gives a smooth, transparent surface, such as a waterproofing layer, and heavier cloth builds thickness, strength and stiffness more efficiently. Three weights cover most work.
| Weight Class | Characteristics And Typical Job | Widths And Roll |
| 4 oz | Surface layer that stops heavier fabric printing through, quick wet-out for canoes and final layers | 30 and 50 inch, 125 yard roll |
| 6 oz (style 3733) | Composite parts, repairs and small craft: low weight, good cosmetics, uniform strength both ways | 38, 50 and 60 inch, 125 yard roll |
| 10 oz (style 7500) | Boats, mold building and lay-up, with layers alternated at 45 degrees to add strength | 38 and 50 inch, 125 yard roll |
By Construction
- Multiaxial: a non-curling structure whose layers are sewn together with polyester yarn. Suited to wind energy, shipbuilding, molds, automotive, aviation and defense.
- Biaxial: fibers run at ±45°, adjustable from +30° to +80°, at 300 to 1200 g/m² and up to 101 inches wide. Suited to parts needing strength in two set directions.
- Unidirectional: 150 to 1200 g/m² in the 0° direction. Suited to parts loaded mainly along one axis.
- Triaxial: adds a third direction to the biaxial layout. Suited to parts loaded in three directions.
By Coating
A coating changes the job and often lowers the temperature limit. Always confirm whether a quoted temperature belongs to the coating or the base cloth.
- Silicone coated: extremely heat resistant and flame retardant. Suited to high-heat and flame protection.
- Aluminized: reflects heat on its coated side while the cloth gives thermal insulation. Suited to insulation fabric for heat reflection.
- PU coated: the coating works at 260°C while the base works at 537°C. Suited to uses within the coating’s temperature limit.
- PVC coated: flame retardant, waterproof and UV resistant. Suited to outdoor and waterproof uses.
- Acrylic coated: heat resistant and cuts easily. Suited to expansion joints and pipe insulation jackets.
Applications And Industry Uses Of Fiberglass Fabric

Each industry asks for a different property, so the specification differs even when the fabric looks the same.
- Boats and canoes: cloth plus resin is the build method, and for large smooth areas with strength requirements the pairing is cloth with epoxy. The weight class sets the layer (4 oz outer, 6 oz small craft, 10 oz structural), and the buyer specifies weight, width and the resin it must wet out with.
- Surfboards: E-glass at about 120 g/m² forms the core and surface, and S-glass at about 200 g/m² goes on edges, corners and tail wings, where it is stronger and abrasion resistant but less flexible. The trade-off is flexibility against local strength, so S-glass is used only where that strength is needed.
- Molded parts and composite materials: molding, lay-up and structural work use the heavier weights, and style 7725 (modified) is listed for complicated shapes at 8.8 oz per square yard and 38 inches wide. Composite materials built on cloth depend on resin ratio, so the cloth and resin system are specified together.
- Aerospace, wind, shipbuilding, automotive and defense: multiaxial constructions carry loads in set directions while staying non-curling for lay-up.
- Electronics: E-glass is the base for printed circuit boards because of its heat endurance, dielectric behavior and erosion resistance. Weave also matters here, because the uneven distribution of glass in a board, known as the fiber weave effect, causes signal skew and timing errors that limit bit rate and trace length, according to IPC technical papers. For these buyers the glass style and the uniformity of the weave are specification items.
- Pipe insulation jackets and thermal protection: cloth has a low heat transfer coefficient, and the air pocket that forms inside a made and installed jacket reduces heat loss from valves, flanges, steam pipelines, joints and containers. The same cloth gives thermal protection against welding slag, where the grade is chosen by temperature.
How To Select Fiberglass Fabric: Decision Sequence And Worked Examples
This section sets the selection criteria. Performance figures are in the properties section and the classification subsections above. Settle these steps in order, because earlier steps limit later ones.
- Job and resin: name the job and the resin first.
- Temperature and time basis: state the temperature and how long the cloth sits at it, then compare it with a rating on the same time basis.
- Glass type: E-glass for general composite and electronic work, and S-glass only for local high-strength areas.
- Weight and thickness: pick the lightest weight that reaches the thickness in a sensible number of layers.
- Weave and construction: choose by drape and load direction: satin for curves, plain for large smooth parts, twill for durability, multiaxial for set load directions.
- Coating: add one only if the job needs it.
- Width and roll: pick a width close to the part dimension to reduce trimming.
When requirements conflict, resin compatibility and the temperature basis win, structure and geometry come next, and finish and width come last. Process matters too: in vacuum infusion, weave and fabric weight change the fiber and void volume fractions, so a test panel is more important there than in hand lay-up.
Three worked examples show the trade-offs:
- A curved molded part laid up by vacuum infusion in epoxy: satin follows the curves, and 10 oz cloth with layers alternated at 45 degrees builds the strength. The trade-off is process sensitivity, so run a test panel before ordering rolls.
- A small epoxy boat repair: 6 oz plain cloth (style 3733) gives low weight, good cosmetics and uniform strength in both directions, and it is transparent. If the repair has to rebuild structural thickness, 10 oz cloth with layers alternated at 45 degrees trades some cosmetics for strength.
- A part that sees 500°C: regular cloth leaves a thin margin below its half-hour rating. If the exposure lasts hours, ask for a continuous rating or move up to medium silica, and confirm the time basis for the part.
Specification Table And What To Confirm In Writing

Before ordering fiberglass fabric, put the style, weight, thickness, width, roll length and weave into the purchase order as numbers. The styles below come from the standard style list.
| Style | Weight | Thickness | Width | Roll Length | Weave |
| 3732 | 430 g/m² | 0.4 mm (page) or 0.43 mm (data sheet) | 1.0 to 2.0 m | 50 m (page) or 100 m (data sheet) | Satin (page) or broken twill (data sheet) |
| 3733 | 5.79 oz/sq yd | Not given | Not given | 110 yards | Plain, 18 x 18 count |
| 3784 | 880 g/m² | 0.8 mm | 1.0 to 2.0 m | 50 m | Satin |
| 7628 | 205 g/m² | 0.2 mm | 1.0 to 1.27 m | 100 m | Plain |
| 3788 | 1700 g/m² | 1.7 mm | 1.0 to 2.0 m | 50 m | Satin |
Three conflicts need a written answer before ordering. Style 3732 shows a different weave, thickness and roll length on the page and the data sheet. The general range of 260 to 1600 g/m² does not cover style 3788 at 1700 g/m² or style 7628 at 205 g/m². And the temperature rating carries two time bases, as described in the properties section.
Tolerances are published for one style only. The 3732 data sheet gives 430 g/m² ±10, warp thread count 18 ±1.8 per cm, weft 13 ±1.3 per cm, and minimum tensile strength of 700 N/5 cm warp and 400 N/5 cm weft. Ask for the same set for every style you buy, plus breaking strength, coating weight and the test conditions behind each temperature. Weight, width, length and label can be customized.
Matching Supplier Capabilities To Buying Problems
In-house yarn drawing and weaving address batch consistency, so ask for batch records that trace your roll to its yarn. A daily output of 200,000 m² of fabric addresses schedule risk, with a 15 day lead time for raw materials and a 1 year warranty. Free A4 samples let you test wet-out in your own resin before volume, and new customers pay 30% deposit and 70% before loading. Custom fiberglass manufacturing covers weight, width, length and label when no standard style fits. On certification, CE, RoHS, UL94 and NFPA 701 each cover something different: CE is a manufacturer declaration, RoHS restricts hazardous substances in electronics, UL94 classifies the flammability of plastics, and NFPA 701 tests flame propagation of textiles. Ask for the report for the exact style, not a company certificate.
FAQs
Can A Sample Approve A Whole Order?
It shows handling, wet-out and finish. It does not show batch consistency, so pair it with the data sheet, batch records and tolerances agreed in writing.
How Much Fiberglass Fabric Do I Need For A Part?
Multiply the part’s surface area by the number of layers, then add an allowance for trimming. Choosing a roll width close to the part dimension reduces offcuts, and the roll lengths in the specification table let you convert the total into a number of rolls.
What Is The Difference Between Fiberglass Fabric And Fiberglass Mat?
Fabric is woven from warp and weft yarns, so its fibers lie in set directions and give predictable strength along them. Mat is a non-woven sheet of randomly laid fibers, which has no fixed direction and is usually chosen for bulk and ease of shaping rather than directional strength.
Why Is The Size Removed From The Cloth Before It Ships?
The size is a coating applied to the yarn to protect it during weaving. The desizing step removes it so the cloth is clean before inspection and packing, which helps the resin bond to the glass.
What Should I Send A Supplier To Get An Accurate Quote?
Send the job, the temperature and how long the cloth sits at it, the target weight and width, and the quantity. If no standard style fits, add the custom weight, width, length and label you need.










